Danh mục sản phẩm


Danh mục sản phẩm > > Honsberg > Temperature Transmitter / Switch OMNI-T

Temperature Transmitter / Switch OMNI-T

Mã sản phẩm: OMNI-T
Nhà Sản Xuất:


Tài liệu hướng dẫn Download
● Analog output 4..20 mA or 0..10 V
● Two programmable switches (push-pull)
● Backlit graphical LCD-Display (transreflective), can be read
in sunlight and in the dark
● Programmable parameters via rotatable, removable ring
(programming protection)
● Full metal housing with non-scratch, chemically
resistant glass
● Physical unit in the display (selectable)
● Rotatable electronic head for best reading position
● Tropical model optionally available
● High temperature model (200 °C) optionally available
● Connection to USB interface for setting parameters
● IP 67

The primary sensor consists of a platinum resistance sensor using
thin film technology, which provides a very good response time,
thanks to the lance diameter of 4 mm.
With these sensors, switching points can be set on the spot for
where process values are exceeded or fallen short of. This setting
can be carried out via the display, even without the process. The
present values, or error messages from the measuring point, are
visible at all times, and all important parameters can be displayed
locally (this saves time during installation, commissioning, and
troubleshooting during the process). The analog current signal can
be evaluated from large distances, and the present values can be
made available there. The sensor is configured to your
requirements. It is therefore ready for immediate use, without
programming. If you wish to change parameters, you can set the
device directly at the sensor, by means of the programming ring.
The entire family of OMNI sensors is made up in a modular way, by
means of a building-block system (hardware and software). A 16-bit
microcontroller with a 12-bit A/D converter and a 12-bit D/A
converter ensures the necessary processing speed and accuracy.
The signal is displayed with the unit of measure by a backlit LCD
graphical display, and is converted into a 0/4..20 mA signal. Two
switching points with push-pull output can be programmed across
the whole range. The hysteresis of the switching points can be set
separately in value and direction (min., max. switching value).
Exceeding or falling short of switching points, and error messages,
are indicated by a flashing red LED visible from a long distance,
together with a message in the display

» Honsberg - Temperature Difference Transmitter ETSD: 0 VND (ETSD)
» Honsberg - Flow Switch G-...GR: 0 VND (G-008..015GR)
» Honsberg - Flow Switch /Indicator TX-...FT: 0 VND (TX-015..200FT)
» Honsberg - Flow Switch MF-007: 0 VND (MF-007GM)
» Honsberg - Flow Switch RVM: 0 VND (RVM-008GM / K)
» Honsberg - Flow Switch FX: 0 VND (FX-015GP)
» Honsberg - Flow Indicator / Switch VF: 0 VND (VF- / VFR-008GM / K)
Liên Hệ Trực Tuyến

Tel: (08) - 6675.2925

(08) - 3511.5746

Fax: (08) - 3511.7931

Hot Line: 0934.101.781



Cảm Biến - Sensor

Lượt truy cập

29-31 Dinh Bo Linh Street, Ward 24, Binh Thanh District.
Telephone: 08-6675.2925      Fax: 08-3511.7931
Email: kd3@cntruongthanh.com
Hotline: 0934.101.781
Copyright © 2010 cntruongthanh.com
Phát triển bởi N N H